Waterloo F1880 Manual de usuario descargar pdf (Pagina 2)

Hardware Included:

TOOLS REQUIRED:

1/2” wrench 3/8” wrench

5/16” drill bit 7/16” wrench

Phillips Screwdriver

Cabinet:

Literature

Hardware bag

Caster pack

CASTER INSTALLATION

SIDE HANDLE ATTACHMENT

Items Needed:

#14 - 10 x 3/4" Phillips Screws (Qty: 4)

Phillips Screwdriver

Chest:

Literature

Hardware bag

• Attach the side handle using (4) #14-10x 3/4 Phillips

screws.

NOTE: There are 2 styles of caster mounting depend-

ing on the cabinet purchased. Choose the style that

applies to your cabinet.

NOTE: Not all assembly instructions will apply to your model.

WARNING

Remove wooden work surface or rubber mat, if any,

before attaching chest(s) to the cabinet.

1/4 - 20 Nut (Qty: 16)

1/4 - 20 x 5/8 Screw (Qty: 16)

5/16 - 18 x 3/4 Screw (Qty: 16)

5/16 - 18 Nut (Qty: 16)

Process:

• Remove bottom drawers. (See Operation Section, Part

B.)

• Lay the cabinet on its back. Use packaging material to

protect the nish.

• Mount both swivel casters on the same side of the unit

as the side handle.

• Attach the casters using (4) 1/4 - 20 x 5/8" screws and

(4) 1/4 - 20 nuts per caster.

• Wrench tighten all screws. It is recommended not to

exceed 80 inch pounds of torque.

• Return the unit to its upright position.

• Reinstall bottom drawers.

Items Needed for 5 x 2 Casters:

1/4 - 20 x 5/8" Screw (Qty: 16) 1/4 - 20 Nut (Qty: 16)

7/16-in Wrench 3/8-in Wrench

Items Needed for 6 x 2 Casters:

5/16 - 18 x 3/4" (Qty: 16) 5/16 - 18 Nut (Qty: 16)

1/2-in Wrench

Process:

• Remove bottom drawers. (See Operation Section, Part

B.)

• Lay the cabinet on its back. Use packaging material to

protect the nish.

• Mount both swivel casters on the same side of the unit

as the side handle.

• Attach the casters using (4) 5/16 - 18 x 3/4" screws and

(4) 5/16 - 18 nuts per caster.

• Wrench tighten all screws. It is recommended not to

exceed 80 inch pounds of torque.

• Return the unit to its upright position.

• Reinstall bottom drawers.

TO ATTACH CHEST

Process:

· Remove enough drawers to access the top and bottom

mounting surfaces of the units. Refer to drawer removal

instructions.

· Place the chest in the desired location on top of the cabi-

net or intermediate chest and mark the mounting hole

locations onto the cabinet top.

· Remove the chest and drill two 5/16" (8mm) holes

through the top of the cabinet or intermediate chest.

· Secure the units together using two 1/4 - 20 x 5/8"

screws and nuts at each joint.

NOTE: Not all operation instructions will relate to your

model.

• Empty the drawer.

• Fully extend the drawer.

REMOVING DRAWERS

RAISE AND RELEASE DRAWER FRONTS

NOTE: These units are equipped with the raise and

release drawer fronts.

• To open, lift up on the drawer front while pulling towards

you.

• To close, shut the drawer rmly until the latch engages.

• Pull back lightly to see if the drawer is completely closed.

• If the drawer does not stay closed, the striker may be

bent, or the striker rubs against the drawer slides.

• To x the problem, lightly bend the striker until the drawer

will engage in the slide.

• Unit not shown for clarity.

Release

2 3

HARDWARE ASSEMBLY

CARTON CONTENTS

OPERATION

#14 - 10 x 3/4 Phillips Screw

(Qty: 4)

5/16 - 18 x 3/4 Screw (Qty: 16)

1 2 3 4 5 6 7 ... 10 11

Comentarios a estos manuales

Sin comentarios

Waterloo F1880 Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Herramientas Waterloo F1880